Pd-MnO2 nanoparticles/TiO2 nanotube arrays (NTAs) photo-electrodes photo-catalytic properties and their ability of degrading Rhodamine B under visible light

Pd-MnO_2/TiO_2 nanotube arrays(NTAs) photo-electrodes were successfully fabricated via anodization and electro deposition subsequently; the obtained Pd-MnO_2/TiO_2 NTAs photo electrodes were analyzed by scanning electron microscopy(SEM), X-ray diffraction(XRD) and characterized accordingly. Moreover, the light harvesting and absorption properties were investigated via ultraviolet–visible diffuse reflectance spectrum(DRS); photo degradation efficiency was investigated via analyzing the photo catalytic degradation of Rhodamine B under visible illumination(xenon light). The performed analyses illustrated that Pd-MnO_2 codoped particles were successfully deposited onto the surface of the TiO_2 nanotube arrays;DRS results showed significant improvement in visible light absorption which was between400 and 700 nm. Finally, the photo catalytic degradation efficiency results of the designated organic pollutant(Rhodamine B) illustrated a superior photocatalytic(PC) efficiency of approximately 95% compared to the bare TiO_2 NTAs, which only exhibited a photo catalytic degradation efficiency of approximately 61%, thus it indicated the significant enhancement of the light absorption properties of fabricated photo electrodes and their yield of UOH radicals.     

流体剪切与超声空化破解剩余污泥的参数优化

为提高剩余污泥的破解效果并降低能耗,采用FS（fluid shear,流体剪切）、UC（ultrasonic cavitation,超声空化）、FS和UC联合工艺（FS-UC,UC-FS）破解剩余污泥,并应用单因素试验结合响应面法对联合工艺进行优化.结果表明:FS对剩余污泥破解效果一般,只在开始阶段具有较好效果,随作用时间延长,破解效果未有显著提高甚至下降.UC对剩余污泥破解效果明显,随作用时间延长,破解效果显著提升,但能耗也随之增大,EDR（energy disintegration ratio,效能比）明显下降.相同作用时间下,UC破解效果优于FS破解效果,UC破解剩余污泥的DD_COD（degree of disintegration,破解率）与EDR均明显高于FS方法.单因素试验得出的较优FS作用时间范围为2~8 min,较优UC作用时间范围为5~15 min.响应面法试验结果显示,联合工艺的剩余污泥破解效果和能量利用率均优于单一方法,联合工艺中FS-UC工艺的破解效果优于UC-FS工艺.FS-UC工艺的最佳参数:FS处理5.6 min再UC处理15.0 min,该条件下剩余污泥实际DD_COD为50.8%,EDR为26.8%.UC-FS工艺的最佳参数:先UC作用15.0 min再FS作用7.8 min,该条件下剩余污泥实际DD_COD为36.5%,EDR为17.1%.研究显示,以DD_COD和EDR为指标,4种工艺的高效性顺序为FS-UC > UC-FS > UC > FS,其中FS-UC工艺具有能耗低、破解效率高的特点,是4种工艺中剩余污泥破解效果最好的一种工艺.      

河北平原潮土中微生物对氮降解特征

了解土壤中微生物对氮素降解规律,对于土壤氮污染修复具有重要现实意义.从河北平原潮土中筛选出8种高效氨化细菌、硝化细菌、异养硝化好氧反硝化细菌,对所筛菌种进行16S r DNA分析,选出最适菌株通过固定化载体将菌种制成菌剂.探讨了用加入所筛菌种及拮抗菌的菌液和地表水分别滴灌小白菜对土壤中的氮降解产生的影响,并测定土样磷脂脂肪酸(PLFA)的值.结果表明:以硅藻土为载体硝化细菌的氨氮降解率达到38%,硝态氮合成率为205%;以硅藻土为载体的氨化细菌氨氮合成率为1 711%,异养硝化好氧反硝化细菌的硝态氮降解率达到367%.加所筛菌液滴灌对土壤总氮和氨氮的降解效果较好,硝化作用也较强,加菌后土壤中微生物量明显增加,且更快到达峰值.对不同土样不同时间磷脂脂肪酸数据分析发现,在白菜生长过程中,土壤中的微生物含量均产生了1次峰值,且加入所筛菌的先到达峰值.对于任丘和阜城土样来说,加入所筛菌后,土壤中微生物种类相应增多,对土壤微生物环境有所改善,微生物也比较活跃.     

光催化降解渗滤液DOM不同组分的相对分子质量变化特征

采用凝胶色谱技术研究了光催化氧化处理过程中垃圾渗滤液DOM 6种组分的分子质量变化规律.结果表明,垃圾渗滤液DOM的相对分子质量大多在104以下,平均在104以上的大分子物质主要是HIB和HIN,仅占渗滤液DOM总量的20%左右.其余组分大多位于(1～10)×103之间,低于500的组分含量很少.说明垃圾渗滤液DOM是以中等相对分子质量的黄腐酸类物质为主,难以生物降解.光催化处理过程中渗滤液DOM的相对分子质量分布范围逐渐变宽,多分散系数D逐渐增大.HOB、HIB、HIA以及HON组分在光催化处理后,相对分子质量显著减小;其中HOB减小最为明显,由初始的(4～25)×103,减小为72 h的(0.4～1)×103之间.而HOA和HIN组分的相对分子质量呈增加趋势,其中HOA增加最为明显,在垃圾原液中分布于(2～20)×103,在72 h光催化处理液中位于(20～50)×103之间.随着处理时间延长,DOM各组分的RID信号均降低,说明其浓度下降.整体上看,渗滤液DOM各组分均发生了明显光催化转化.     

含藻水中壬基酚的光降解转化研究

选取壬基酚(nonylphenol,NP)作为研究对象,研究了水中2种常见淡水藻(小球藻和鱼腥藻)对壬基酚的光降解促进作用,并对藻引发水中壬基酚的光降解途径进行了分析;同时也研究了天然水中普遍存在的物质成分(腐殖酸和铁离子)与藻协同引发壬基酚的光降解及其影响机制.结果表明,含淡水藻的水溶液经过光照后能引发其中壬基酚的光降解;藻、腐殖酸和铁离子的水溶液经过光照后,对壬基酚光降解的增强促进作用更大,在含藻、腐殖酸和铁离子的水溶液中,4 h光照后壬基酚的降解率可达58%.根据此结果推测藻/腐殖酸和铁离子体系光照后能产生更多的活性物质,从而促进水中有机污染物的光降解.     

链霉菌FX645对偶氮染料红AR30的降解机制研究

从印染厂污泥中筛选到1株对偶氮染料红30(AR30)具有较强脱色降解作用的菌株Streptomyces sp.FX645.通过降解产物的紫外-可见吸收光谱、LC-MS分析及各降解产物在发酵体系中浓度随时间变化的规律,探讨了菌株FX645对AR30的可能降解途径,首先在偶氮还原酶的作用下AR30发生偶氮键的裂解,生成4-硝基-2,6-二氯苯胺与2-[(4-胺苯基)-(2-氰乙基)-氨基]乙酸乙酯,然后分别发生硝基还原、氨基酰化、氰基水解作用,生成一系列的苯胺类化合物.     

氟虫双酰胺在水稻和稻田中的残留动态研究

采用超高效液相色谱法(UPLC)测定了氟虫双酰胺19.8%悬浮剂(SC)在水稻及稻田环境中的残留动态.结果表明,当氟虫双酰胺及其代谢产物NNI-des-iodo的添加量为0.05～1.0 mg·kg-1时,其在水稻田土壤、田水、稻秆、稻米和稻壳中的平均回收率为78.2%～104.8%,变异系数为1.1%～4.4%.氟虫双酰胺在2011年三地(福建福州、天津、江苏南京)的稻田水中的降解半衰期为9.8～17.3 d,土壤中10.8～22.4 d,植株中7.6～17.3 d,其在稻田水样品中检出了代谢产物NNI-des-iodo,而在土壤和植株样品中未检出.在推荐使用剂量下,于末次施药10 d后,氟虫双酰胺在水稻稻米中的残留量均低于美国规定的在稻谷上的最大残留允许量(0.5 mg·kg-1).     

Utilizing surfactants to control the sorption, desorption, and biodegradation of phenanthrene in soil-water system

An integrative technology including the surfactant enhanced sorption and subsequentdesorption and biodegradation of phenanthrene in the soil-water system was introduced and tested. For slightly contaminated agricultural soils, cationic-nonionic mixed surfactant- enhanced sorption of organic contaminants onto soils could reduce their transfer to plants, therefore safe-guarding agricultural production. After planting, residual surfactants combined with added nonionic surfactant could also promote thedesorption and biodegradation of residual phenanthrene, thus providing a cost-effective pollution remediation technology.0ur results showed that the cationic-nonionic mixed surfactantsdodecylpyridinium bromide (DDPB) and Triton X-100 (TX100) significantly enhanced soil retention of phenanthrene. The maximum sorption coefficient Kd* of phenanthrene for contaminated soils treated by mixed surfactants was about24.5 times that of soils without surfactant (Kd ) and higher than the combined effects of DDPB and TX100 individually, which was about 16.7 and 1.5 times Kd , respectively.0n the other hand, TX100 could effectively remove phenanthrene from contaminated soils treated by mixed surfactants, improving the bioavailability of organic pollutants. Thedesorption rates of phenanthrene from these treated soils were greater than 85% with TX100 concentration above2000 mg/L and approached 100% with increasing TX100 concentration. The biodegradation rates of phenanthrene in the presence of surfactants reached over 95% in30days. The mixed surfactants promoted the biodegradation of phenanthrene to some extent in 10-22days, and had no obvious impact on phenanthrene biodegradation at the end of the experiment. Results obtained from this study provide some insight for the production of safe agricultural products and a remediation scheme for soils slightly contaminated with organic pollutants.     

Photocatalytic degradation of carbofuran in TiO2 aqueous solution：Kinetics using design of experiments and mechanism by HPLC/MS/MS

The photocatalytic degradation kinetics of carbofuran was optimized by central composite design based on response surface methodology for the first time. Three variables, TiO2 concentration, initial pH value and the concentration of carbofuran, were selected to determine the dependence of degradation efficiencies on independent variables. Response surface methodology modeling results indicated that the degradation efficiency of carbofuran was highly affected by the initial pH value and the concentration of carbofuran. Then nine degradation intermediates were detected by HPLC/MS/MS. The Frontier Electron Densities of carbofuran were calculated to predict the active sites on carbofuran attacked by hydroxyl radicals and photoholes. Point charges were used to elucidate the chemisorption pattern on TiO2 catalysts during the photocatalytic process. By combining the experimental results and calculation data, the photocatalytic degradation pathways of carbofuran were proposed, including the addition of hydroxyl radicals and the cleavage of the carbamate side chain.     

纳米Fe_3O_4/膨润土的制备、表征及光催化降解焦化废水

以铝柱撑膨润土负载纳米Fe_3O_4制备出性能良好的复合型催化剂。结合X射线粉末衍射(XRD)、扫描电镜(SEM)和比表面孔隙分析(BET)对催化剂的晶相、比表面积和粒度进行表征。负载的纳米Fe_3O_4粒径约为20～30nm,均匀分散到膨润土表面,未发生明显的团聚。在紫外光作用下用该催化剂对焦化厂二沉池出水进行深度处理。结果表明,在催化剂投加量为0.7 g/L,pH为2.5,温度40℃,H_2O_2初始浓度为17.6mmol/L的反应条件下,二沉池出水(化学需氧量COD=140mg/L,色度=400度)经催化氧化降解后,COD和色度可分别降低到54.44 mg/L和10度,达到国家工业再生用水水质标准GB/T 19923-2005(COD≤60 mg/L,色度≤30度)。催化剂重复使用4次时,废水COD和色度去除率保持稳定。